CCNA Basics

By

 CCNA Basics


Cisco Basics (CCNA level) Lessons:

Lessons:

01 - Connecting to Cisco Console Port with MINICOM
02 - Navigating in Cisco IOS
03 - Initial Configuration of Cisco Switch and Router
04 - Introduction to TCP/IP Layers
05 - Encapsulation and De-enapsulation Process
06 - Example of TCP/IP Traffic Flow
07 - Building a Home Network
08 - Ethernet and Hub Operations
09 - Bridging/Switching Learning Process 
10 - Cisco Discovery Protocol 
11 - Layer 2 Connectivity Troubleshooting Part 1
12 - Layer 2 Connectivity Troubleshooting Part 2
13 - Layer 2 Connectivity Troubleshooting Part 3
14 - NTP and Syslog Services
15 - VLANs Overview
16 - VLANs In Practice
17 - Inter VLAN Traffic Flow Analysis
18 - VTP and VLAN Quiz
19 - Spanning-Tree Protocol Overview
20 - Spanning-Tree Protocol Operation
21 - Spanning-Tree Protocol in Practice
22 - Spanning-Tree Cisco Enhancements
23 - Introduction to Rapid STP (802.1w)
24 - Layer 2 Etherchannel
25 - Switch Port Security
26 - Binary World
27 - IPv4 Address Dissected - Part 1
28 - IPv4 Address Dissected - Part 2
29 - IPv4 Subnetting - The Rules
30 - IPv4 Subnetting - Practice
31 - What is a Router?
32 - Route Selection Process Demistified
33 - Static Routing
34 - Dynamic Routing Protocols Introduction
35 - Routing Information Protocol Part 1
36 - Routing Information Protocol Part 2
37 - Routing Information Protocol Part 3
38 - OSPF Fundamentals Part 1 - Terminology 
39 - OSPF Fundamentals Part 2 - Hello Packets
40 - OSPF Fundamentals Part 3 - RouterID and DR/BDR
41 - OSPF Fundamentals Part 4 - Implementation
42 - OSPF Fundamentals Part 5 - The Lab
43 - EIGRP Fundamentals Part 1 - Overview
44 - EIGRP Fundamentals Part 2 - Implementation
45 - EIGRP Fundamentals Part 3 - The Lab
46 - EIGRP Fundamentals Part 4 - Troubleshooting
47 - Packet Filtering with Standard ACL
48 - Standard ACL Examples
49 - Packet Filtering with Extended ACLs
50 - Extended ACL Examples
51 - Network Address Translation Part 1 - Terminology
52 - Network Address Translation Part 2 - Principles of Operation
53 - Network Address Translation Part 3 - Overloading Addresses
54 - Network Address Translation Part 4 - Configuration Examples
55 - Introduction to IPv6 Part 1 - Addresses
56 - Introduction to IPv6 Part 2 - Address Structure
57 - Introduction to IPv6 Part 3 - Address Configuration
58 - Introduction to IPv6 Part 4 - Migration  

How to install and Use IOS on Linux.

Disclaimer!

Comments

Post a Comment

Popular posts from this blog

Lesson 27 - IPv4 Address Dissected - Part 1

By
Image
Lesson 27 - IPv4 Address Dissected - Part 1 If you already feel comfortable with binary-to-decimal and decimal-to-binary conversions you're up to this post's challenge: learning more about IP version 4 address (IPv4). If you need to brush upon the numeral conversions, check my  previous post . In one of the earlier posts on  TCP/IP traffic flow , I briefly described the importance of the addresses. In order for devices to communicate they must be uniquely identified in the network after all. There are typically three such identifiers we use to distinguish between devices: Names  - These are used by humans. Applications use addresses not names. Hence, DNS services out there (DNS service is used to resolve names-to-ip, and ip-to-names).  Layer 3 addresses  -  logical  and  hierarchical  unique identifiers of devices in the network. All layer 3 protocols such as IPX, Apple-Talk, IP etc. use different forms of layer 3 addresses.  Layer 2 addresses  -  flat  and most ofte
Read more

Lesson 21 - Spanning-Tree Protocol in Practice

By
Image
Lesson 21 - Spanning-Tree Protocol in Practice Previous post was designed to present in a nutshell the STP operation. However, without some practice it's just academic knowledge. I think it is a good idea to look at the same concepts using real equipment. Here goes... The below topology (pic. 1) uses redundant links which create the loops. Pic. 1 - Network Topology Icons designed by: Andrzej Szoblik -   http://www.newo.pl If there's one thing the administrator should do with such design, that would be configuring the root bridge. Typically, the most powerful switch in the center of the network plays that role. You do not want some access switch to be transmitting the frames between other switches. Access switches are designed to connect your computers to the network, and not to handle the majority of the traffic between the switches which root bridge must deal with. If you do not configure root bridge yourself, the switch with the lowest MAC address becomes th
Read more

Lesson 4 - Introduction to TCP/IP Layers

By
Image
Lesson 4 - Introduction to TCP/IP Layers In this lesson we take a sneak peek at the fundamentals regarding TCP/IP. This is one of the most important aspects to understand in order to follow the upcoming lessons. It is not my ambition to explain everything here as this would turn into a hefty book to read. You can find a lot of them on the market anyway. Instead, I will try to focus on some basic aspects of TCP/IP. They will constitute the minimum knowledge to help us understand how computers communicate. If you feel the urge to learn more on TCP/IP right now please visit the following site:  http://www.tcpipguide.com/free/t_toc.htm NOTICE! Familiarize yourself with ALL terms in red. They will be used throughout the classes. Introduction Computer communication follows some well defined rules and guidelines which we call  protocols . In order for the computers to exchange data they have to agree on using the same rules, otherwise they become incompatible. That was the case in t
Read more